1. Some members were not receiving emails sent from XJbikes.com. For example: "Forgot your password?" function to reset your password would not send email to some members. I believe this has been resolved now. Please use "Contact Us" form (see page footer link) if you still have email issues. SnoSheriff

    Hello Guest. You have limited privileges and you can't "SEARCH" the forums. Please "Log In" or "Sign Up" for additional functionality. Click HERE to proceed.

86 XJ sputters between 1000 and 2000 RPM's

Discussion in 'XJ Technical Chat' started by jimwrixon, Dec 11, 2006.

  1. jimwrixon

    jimwrixon New Member

    Messages:
    10
    Likes Received:
    0
    Trophy Points:
    1
    Location:
    CA
    Could someone make a suggestion? My 86 XJ700XS sputters between 1000 and 2000 RPM'S. I have cleaned all carbs, set float levels, re-synced the carbs, changed spark plugs, checked compression, and adjusted the valves. This makes it a little difficult to take off, but otherwise it runs good.

    Any suggestions would be appreciated.
     
  2. FinnogAngela

    FinnogAngela Member

    Messages:
    205
    Likes Received:
    1
    Trophy Points:
    16
    Location:
    Copenhagen, Denmark
    Mine did the same thing - turned out to be bad coil/wire connections; the PO had tried to repair them by just pulling out the ignition wires and showing new ones up the outlet holes. Found out they were bad by measuring the secondary resistance (between the two ignition wires on each coil, spark plug caps off).
    Above 2500rpm the sputtering went away; guess the increased rpms/alternator output overcame the bad connections.
    You also might wanna check the ignition wire/spark plug cap connection for corrosion..
     
  3. jimwrixon

    jimwrixon New Member

    Messages:
    10
    Likes Received:
    0
    Trophy Points:
    1
    Location:
    CA
    Thanks Finn. Could you make a suggestion for wires? What type or brand?

    Jim
     
  4. samsr

    samsr Member

    Messages:
    599
    Likes Received:
    3
    Trophy Points:
    18
    Location:
    Colorado Springs
    my xj did that this spring. Believe it or not it turned out to be the alternator/generator brushes. They were at minimum. Dont know what your specs are mine are 17mm brand new and 11mm minimum. If they are close to minimum then I would change them. Extra power means a better spark. Runs like a raped ape now. The rest is history. Some one here could probably tell you what the specs are on you bruches.
     
  5. FinnogAngela

    FinnogAngela Member

    Messages:
    205
    Likes Received:
    1
    Trophy Points:
    16
    Location:
    Copenhagen, Denmark
    --------------------------------------------------------------------------------
    jimwrixon wrote:
    Thanks Finn. Could you make a suggestion for wires? What type or brand?

    Jim

    Jim, if you need to change wires on the old coils it´s a bit complicated (but can be done). You have to cut/dremel/hacksaw open the coils to fit the wires and close them again with epoxy/silocon putty/etc. The repair can be seen here: www.xs11.com/forum/sho...readid=137
    and here: www.surenet.net/~verhe...coils.html

    I went for the Dyna-coil upgrade and am yet another happy customer: Bike starts easier and generally runs a little better I think (+ they should be better in moist/wet riding). The fitting is a little tedious but it can be done with a little work: www.i-op.com/jimm/dynacoils-on-700/
    (I just drilled holes in mine but can´t recommend it unless you have professional drilling tools - and can measure very accurately..last pic shows my effort): http://hjem.get2net.dk/xjmaximdk/udstmod.htm#coils

    I bought a set of Dyna 8mm supression wires but wasn´t satisfied with the terminals at the coil end (impossible to fit to the cables without a proper crimp-tool and many have reported 8 mm. wires to be difficult to fit into the coil-output). I went with ordinary 7mm Bosch copper-core wire (cheap and available anywhere) and some "screw-on" terminals, which gave me a good "click" connection in the outputs - and like the original ignition wires, screwed easily on my excisting NGK resistor spark plug caps. More on cables the different coil-terminals here: www.skylinc.net/~hap/m...coils.html

    Finally I agree with samsr; the story on my alternator brushes: xjbikes.com/Forums/vie...=2428.html
     

Share This Page