the piston seal deforms a little as the piston gets pushed out, when the pressure is relieved the seals try to return to original shape and they...
if you can't find your originals, maybe go here and take some measurements of yours and find something similar
you could move the start button down by the footpeg and just kick that
WARNING, REDNECK FIX
i found a o-ring that fit tight in the groove on the fuel pipe but didn't quite go into the carb. then i pushed harder, then...
what do you expect for $10
the bolt that clamps the lever to the shaft would defiantly be reuseable
if you have to ask, you can't
if it runs, ride it
maybe it didn't crank fast enough, maybe the gauge was off
This is a good time to work on that spare carb rack, i'm no expert but i doubt corona lives very long on your hands with gas and carb cleaner....
what's wrong with this picture ?
i do know what happened to mine. put the bolts in finger tight, went for lunch, had a few beers, put the cover on and a...
just get a set for a car. i think they take 7mm wire
i was given a .22 rifle because the guy oiled it up with WD40, put it in a case, a year later he almost shot his wife. because the firing pin was...
keep a micro-fiber rag in your jacket pocket to wipe your shield
when i think i need a bike to go faster, i just find a road with tighter turns
paint stripes, tape stripes, metal plates, tar patches are all slippery.
try locking the back wheel at 25kph just to see how it feels, you can try...
when the bike is parked and your not touching anything, the clutch is engaged. the motor is connected to the wheel.
when you pull the lever to...
i tried to use rotella once, then i saw bunches of kinds of rotella. went back to my trusted moble delvac 1300 super, because it was the only one...
that looks like my mac pipe, if the header flanges are soft as butter, it's a mac. i think the name and #'s are on the muffler
that head looks good to me
? would you prime it somehow?
? how much oil pressure would you expect there to be one of these?
the air jet determines the vacuum applied to the fuel jet, the tiny low jet needs lots of vacuum. the high jet not so much.
i had marks on the valve cover from the cam chain. can't imagine how that could happen, but it did/does
maybe when things are just right, it might...
bmw K bikes use the same diameter shim
i want my Cushman Eagle back, two speed suicide shifter with a foot clutch and torque converter
mine does the same thing. get a clear in-line fuel filter, turn it to prime and don't try to start it until the bubble in the filter stops moving,...
be easier to get a honda
there's no aluminum there. to use anything other than gasket in a tube your going to have to get rid of the chrome in the hole and it's...
i tried that a few years ago on a 750
i think i only went 3 deg. didn't notice anything different so i put it back
put some grease on the forks go hit some bumps and see just how much travel your getting
small fuel-big air
big fuel-small air
the plates have to be open for it to run
as soon as you adjust the idle they'll be open even more, then the running sync takes care of any...
that fellow is going to have a good time adjusting the steering bearings on his new forks
that arm looks ok. it's been awhile all i remember is it has one long pin in that cam wheel and it needs to be in the right place
i think the mufflers look fine. did you use simple green in the u sonic cleaner? it don't like aluminum
tensioner, like a spring loaded thing to keep the chain tight, no
there's a rubber/plastic guide and a oil squirter, chacal has both of those
the lights on my battery tenders finally turned green, 4 days.
time to take one out to the cub cadet
bare frame to bare metal. rustoleum hammered silver with rustoleum black added till i liked it, never to be matched :(
engine is Eastwood engine...
i tried several times to use that stuff, R/C airplane engine, (fail,motor mount lug melted) lawn mower deck, (fail, couldn't get the deck hot...
i did a silver frame and engine, i still kind of like it
like white fluffy stuff that wipes off? i get that with some soaps in the little HF ultrasonic if their not rinsed real well. sometimes they get...
synced running on the bike? try 2.75 turns out
tip the frame up on the back, be ready to catch nasty water that might be in the frame. then look at the frame where the side stand is welded....
wait till you try to put it back
looks like it wants to go fast. i can't see that motor in a adventure type bike though, mx maybe
is that a water cooled, 2 cylinder 2 stroke 250, kind of strange. bet parts are even more rare
it's better to be down here, wishing you were up there, than to be up there, wishing you were down here