1. Some members were not receiving emails sent from XJbikes.com. For example: "Forgot your password?" function to reset your password would not send email to some members. I believe this has been resolved now. Please use "Contact Us" form (see page footer link) if you still have email issues. SnoSheriff

    Hello Guest. You have limited privileges and you can't "SEARCH" the forums. Please "Log In" or "Sign Up" for additional functionality. Click HERE to proceed.

Search Results

Search Again
  1. rozko
    Post

    hard to start- never ending story

    Hi guys! here are resoults after measuring compression at 2 cyl. 117 psi! K-moe has right new rings has to seat. Bike starts immediately hot or...
    Post by: rozko, Nov 15, 2015 in forum: XJ Technical Chat
  2. rozko
    Post

    hard to start- never ending story

    I do not believe! Motorcycle fired after 4-5 seconds of cranking. Completely cold! before it was impossible. Now idles for about 30 minutes ....
    Post by: rozko, Nov 11, 2015 in forum: XJ Technical Chat
  3. rozko
    Post

    hard to start- never ending story

    i dont hone cylinder bores because there was still some of factory honing. compresion on cyl 3 goes up after puting manny times petroleum into...
    Post by: rozko, Nov 11, 2015 in forum: XJ Technical Chat
  4. rozko
    Post

    hard to start- never ending story

    Hi, so I've check cylinder bores and they are in spec, for safety replaced piston rings on cylinder 2. all pistons was cleaned and measured...
    Post by: rozko, Nov 10, 2015 in forum: XJ Technical Chat
  5. rozko
    Post

    hard to start- never ending story

    ok I finaly borrowed another compression meter, and the results were the same, but aprox 10 psi lower on each cyl so it could be because of meter....
    Post by: rozko, Sep 5, 2014 in forum: XJ Technical Chat
  6. rozko
    Post

    hard to start- never ending story

    ok forom beginning, I romoved every silgle ruber piece incl throttle shaft seals before dipping in carb cleaner i removed caps from idle...
    Post by: rozko, Aug 31, 2014 in forum: XJ Technical Chat
  7. rozko
    Post

    hard to start- never ending story

    First i dipped carbs in a carb cleanig solution based on toulen. then i spreyed carb cleaner under hi prosure in every passage and using wire...
    Post by: rozko, Aug 30, 2014 in forum: XJ Technical Chat
  8. rozko
    Thread

    hard to start- never ending story

    Hello, my bike have problems with starting since i remember. its XJ550 1984, aprox 30 000 miles things ive check/replace: -full carbs clean...
    Thread by: rozko, Aug 29, 2014, 21 replies, in forum: XJ Technical Chat
  9. rozko
    Post

    Voltage drops problem

    Greenbike Ive try this after pourhasing the bike. Polock thank you i will convert to metric and try to find them in my local suplier. I will...
    Post by: rozko, Mar 25, 2014 in forum: XJ Technical Chat
  10. rozko
    Post

    Voltage drops problem

    Polock so uou say that i can simply replace the seals with the orings? that would be great! is that safe and long term solution? and what do you...
    Post by: rozko, Mar 24, 2014 in forum: XJ Technical Chat
  11. rozko
    Post

    Voltage drops problem

    Ok guys, i dissembled carbs again and clean them in ultrasonic cleaner this time ive break the rack, ive notice that throttle shaft seals are...
    Post by: rozko, Mar 24, 2014 in forum: XJ Technical Chat
  12. rozko
    Post

    Voltage drops problem

    Gas is fresh,valves set (one was too tight), float levels are good( litle bit below floatbowl and carb line) its a second battery tested in shop...
    Post by: rozko, Mar 16, 2014 in forum: XJ Technical Chat
  13. rozko
    Post

    Voltage drops problem

    fresh news from battle field, battery fully charged 12,6v on battery, bike voltometer shows little bit under 12... ground point on frame clear and...
    Post by: rozko, Mar 15, 2014 in forum: XJ Technical Chat
  14. rozko
    Post

    Voltage drops problem

    thanks for advice guys, where i can find frame grunds? i found only one under air filter housing. Polock hard to say because i dont have...
    Post by: rozko, Mar 14, 2014 in forum: XJ Technical Chat
  15. rozko
    Thread

    Voltage drops problem

    Hi all, ive start to work on a project bike xj550, and ive got problem with voltage, aterer turning ignition it have 11,5 max v, when cranks 8-9v....
    Thread by: rozko, Mar 14, 2014, 23 replies, in forum: XJ Technical Chat
  16. rozko
    Post

    RobbieRobot Cafe Racer Project in pictures

    Thanks RobbieRobot!
    Post by: rozko, Aug 25, 2013 in forum: XJ Modifications
  17. rozko
    Post

    RobbieRobot Cafe Racer Project in pictures

    Hi, what kind of rear fender is that? Im looking for spmething like that but without any succes...
    Post by: rozko, Jul 31, 2013 in forum: XJ Modifications
  18. rozko
    Post

    1981 XJ550 Seca rozko's cafe racer

    hi, its a beautifull day outside to spend in a garage, some carb job done [img] un fortunately one regualation screw was imposible to...
    Post by: rozko, Apr 21, 2013 in forum: XJ Modifications
  19. rozko
    Thread

    1981 XJ550 Seca rozko's cafe racer

    Hello! this is my first post on this forum but ive read alot hare. some facts: bought this seca some time ago, for 500 $, Shy was in good...
    Thread by: rozko, Apr 20, 2013, 3 replies, in forum: XJ Modifications
Showing results 1 to 19 of 19
Search Again