No, not with a working system The starter is enabled by either the neutral switch OR side stand up AND clutch pulled in. If in neutral it should...
This one on eBay looks decent and it is fairly priced https://www.ebay.com/itm/375107196304?
This link has color diagrams https://members.tripod.com/dave_jack/Temp/id39.htm The FSM and Haynes both have electrical diagrams. The FSM will...
That depth should be 62mm or about 2.4 inches. I can't see what you are bottoming on in the picture - perhaps the old piston is still in there??...
To evaluate a tachometer active signal wire you really need a scope to see the pulses. The best you can do with a DMM is if it has a frequency...
I am confused on the question as you stated the kit from XJ4ever had the piston, which I believe they sell an OEM kit Anyways, the size is:...
If the warning light is not flashing and all indicators are displayed then the CMS has switched back to standby mode just like when you first turn...
Maybe because sometimes the seats are pitted making the petcock trash; or you could mod it to be a manual and be on your way :-)
If this is the gauge you used: https://www.wwag.com/step/pdf/247312.pdf Then the purple wire (warning) would replace the B/R wire in the below...
They should go through a sequential check of each possible fault illuminating the single icon currently under test. If no faults are detected,...
One member? I believe they are similar to other CMS systems in that the icons are displayed when power is applied as depicted in the above diagram...
Are you saying the fuel icon is displayed, but not the others? You need two fuses and a good ignition switch to supply power to the CMS (Computer...
Good to hear, and hopefully the new one has the same reliability as the Yamaha OEM
Is that timing you are referring to? Didn't the 80 and 81 lack the side stand switch so no ignition cutoff, which means he would be giving up that...
I was thinking XS is six pin rectifier, and the XJ is a 9 pin rectifier / regulator I would suggest testing it before powering it up on the bike...
The Atari is cool and adds some nice safety checks :) That is a reed switch that is used for the self cancelling unit and it is controlled by...
He does, but I am guessing that is not a technically correct answer to your question as the 12V green to ground seems to overrule that
It does work on the XJ series, and I sometimes suggest it. However, in this case Michael has reported (most don't) 12 V on the green wire, which...
You have three regulators? How many did you try? Try posting a picture of your setup with measured voltage clearly visible on DMM
I know very little about the XJ600 but thinking this thread showing the 1991 TCI hookup covers it...
The sensor comes out by removing the circlip and pushing up and out of the reservoir. There is an O-ring there that should be replaced if you take...
This thread has a picture of the Xj1100 TCI, and then since it is not clear they wrote it down. It comes out to this and I added (xxxxx)...
The FSM doesn't get into replacing the film, but it does cover replacing the LCD glass, which pretty much gets you there I don't know if the OEM...
I used this one and ordered their smallest sheet:...
Should be inside headlight bucket a Brown and Green/Yellow bullet connector
The two sides look to be mounted with M4 x 16 (.7) with a captive flat washer, three on each side The center piece is two M6 x 24 (1.0) with a...
What kind of numbers are those? With new jets and older engine they have likely changed so a color tune would be nice, or try the lean drop method...
That will bypass the ignition switch, but make sure the L (blue) input 12V is there to the ignition switch to verify the wiring is OK. I would...
I am looking at the Haynes manual for the UK model and you have a switch to disable that circuit and it has three positions - Off, PO, and On;...
This explains the locking mechanism pretty good https://www.xj4ever.com/clean%20and%20lube%20the%20ignition%20switch.pdf
The stator is under that larger round cover just under the carbs and in front of the starter. Your note states battery 14.3V, but doesn't say...
The bulb flickers now because of the LED bulb and the starter cutoff relay coil producing a voltage when current is stopped. It is way too little...
I have XJ750RH Service Manual and looks like the closest it gets is cable routing, didn't see any frame dimensions
Yes, the DMM will measure from green to black - I added the negative connection above that I left out And I should have added be careful when...
So a very basic test on the regulator section of the Rect/Reg Assembly. The 6 ohm resistor is taking the place of the field coil. And as far as...
A learning process and sorry to see, but curious if you drilled the staked portion of the torx screw before attempting to remove, and was an...
So I am just about out of ideas, but thought I would ask are you running directly from the battery? No charger connected I hope? I will post a...
This is what I used, purchased from Ace Hardware in 2104 so not sure they still carry it. I think actual MEK has been discontinued for sale in...
Kreem lasted 30 years in my tank and then started to flake a bit. Acetone works with patience of letting it soak, but the MEK (deadly stuff) would...
https://www.xj4ever.com/downloads.html will get you to: https://www.xj4ever.com/hitachi%20throttle%20shaft%20seals.pdf Len does have kits,...
So it sort of confuses things further or maybe indicates more than one issue since you are reporting 4.8 ohms from brown to green and that...
Have you checked the fuel level in the carbs, did you wet set them? https://www.xj4ever.com/setting%20fuel%20levels.pdf Did you make sure the...
I never say never with electronics, especially when dealing with a black box (regulator) where we don't know exactly how it is intended to work....
As in split cases, and was that the guide breaking up? This thread is similar, but had a broken guide and after repair they had a lockup in 1st,...
https://www.xjbikes.com/forums/threads/xj-parts-catalog-section-c-fuel-system.44642/ Use find function to search above link with:...
https://www.xj4ever.com/inside%20your%20carbs.pdf It's part of the XJ4Ever.com downloads full of good information...
It could, but my first thought is the mechanical mechanism is corroded creating enough friction that it is difficult for the electromagnet to...
Good that it is working, but from the sound of that the starter / headlight switch might need some attention. When you push the starter switch it...
I think if you look closely you will see the meter is diplaying 50 mV Quite normal if you have a load upstream as the current from the headlight...
I would say yes some can. If the cover is removed you can look for corrosion causing problems with the movement or with the contacts. If the...