This only works if the keys are the same type Single slot left or right Double slot left or right
Your 83 shares gauge cluster with 82,83 xj650 maxim if you can't find one closer I think I have one
I use yamahapartsnation.com to look up part numbers
Have progressive rears on my 650 Seca and are far better than original ones
All Canadian bikes had resistor plugs and 5k caps
I had those on my bike previously and it is a very firm ride Going fast it's ok but the standard spring I have now is better Ps keep them waxed...
I do have a spare 650 seca motor if you are still looking complete but for the clutch cover I can do a compression test also Ps it is a later yics...
Would it be easier to install a 900 motor and carbs into your 650 same as putting a 396 Chevy into the Nova that came with a 283
Have you checked the valve clearance, tight valves will cause loss of compression and result in zero power or not start when warm How about coils...
Is that the maxim caliper ? How many do you want
I live south of Vancouver bc and have no problem getting everything I need and I have a few xj's Where in Canada do you live?
Update Each piece is sold separately The 1265 is just the long wedge driver First one 57001-1266 2. 57001-1267 3. 57001-1293
I have a special tool for wheel bearing removal that has never failed Wedges in bearing's and one or 2 whacks it's out Special tool available from...
You can punch them out from the opposite side The sleeve between the bearings will move enough to get a long punch on it
Just south of Vancouver about 500 yards from the border Easier answer is what do you need
Yes and I have shipped there before A member in Nelson NZ
I'm pretty sure I have 1 or 2 if not @hogfiddles will
If your not running a stiock airbox then moisture may be entering through the crankcase vent or your bike has been parked a long time and just...
3 pin is later automotive style and will work
Merry Christmas big D We should all send you an old signal light for next Christmas to really do up the tree and maybe set a Guinness World Record...
If it’s an H4 bulb then just don’t ride fast in the dark
It is just we call it oxidation red and silver best of both worlds
I think I have an 82 harness I’ll check my huge pile of parts
1980 xj650 maxim side cover set Posting here first Red, all tabs good One small crack in the right one $100 usd plus shipping about $20
Have you tried a rad shop to have a new core put in it
Looked at the listing and seat pan appears correct
May have both of those
If you have the 82 xj750j then any xj650 maxim or 83 xj750j maxim will fit you just won’t have a fuel warning light
Sound like you want 83 maxim gauges and even the 650 ones will work for you
My list doesn’t have enough space on this forum I’ve owned more bikes than pairs of underwear and that’s no joke! Being in the industry for so...
$4100 a bit hefty imo
Just weld it
The whole thing comes apart
Should have one
Not if you ship it to me and he picked it up at my place (Point Roberts Washington) if not I may have one in the barn
I’m going at say that if tire slips of bead it was never seated correctly.
I have a set all done and ready to ride did throttle shaft seals as well bike was crashed 1000 kms after they were done
That exhaust is sold
@hogfiddles will have some
Looks more like 750 Seca style
Stripped screw? Clogged passage? There are a few tricks to deal with those problems . If those don’t work I have a bowl for you.
Those are the most expensive parts I’ve ever seen. If they were new in box maybe. Oem look seat cover is about 50$ ( I did my seat) rear cowl...
I think the upper clamp is the same as the xj650 maxim
No to sandpaper! One or more of the slides are stuck closed? Are the jets in correct location? A good cleaning of all jets and passages Check...
What part is it and how much are they asking?
Almost identical to the “X” that has a fuel level sensor
No someone scooped it just before I was going to call
I know it a “Duh” answer but with sub zero temp and 6-8” of snow getting there is a bit of a challenge until next week or so. I have a truck but...
[ATTACH] This popped up on Craigslist today
You could buy a mint xj for the price of the parts and labour to do a total overhaul on a set of cbx carbs. Had someone ask a few years back and...