Looks like the valve over to me ?
Purchase mine from Len at xj4ever.com. I really don't like cheap aftermarket parts and your usually better leaving on the old parts then...
Order it on Amazon, motorcycle fuel line or just go to a auto parts store, take a open end wench and measure the outside diameter of the hose get...
Should work and I suspect that you have a sync tool ?
Agree with Rooster 53 sounds like the Butterfly's or Throttle plates are hanging up or not set correctly.
Only need to do that if you have a issue ?
Sometimes the Float Needles and Seats even in good condition will not seat correctly as it just happens which is a another reason to never leave...
I suspect that the fuel evaporates in the bowls after sitting for a period and that is the reason for using the prime, you sure don't want to...
Adjustments are repairs in the life of nuts and bolts and tuning engines.
Like XJ 650 said, I had the same issue after a frustrating day and it would be nice if someone would post the exact procedure on doing this repair...
I just used a piece of rubber hose and lubed it up well and shoved it though that port and that sealed it up well enough to set my carbs, there is...
I really don't remember having a issue removing the switch it self but I also have a lot of tools too, I heard of some cleaning the switch but...
On my bike I did remove the exhaust but not the oil pan and if my memory is correct the wiring was a bit of a pain.
Easiest and cheapest in my opinion is find a used motor Ken. Can you post some photos ?
I feel your pain as do many others that are on this site, my bike is running good now but it wasn't easy for me ether. As for your issue I agree...
Local Dealer does exchange for me, stay away from the cheap after market ones as they don't fit correctly in the bucket and some sizes are fewer...
I install a 1 inch by 2 inch about 5 inch long piece of lumber in-between exhaust pipes 2 and 3 on the frame rail with a car screw jack.
Did Len have a tool for that procedure ?
I believe that Len at XJ 4 EVER sells a tool to remove race ?
Does anyone know what kind of grease Yamaha used on original wheel bearings ?
Was able to duplicate noise while turning wheel and applying hand brake but it would have been nice to have another set of hands LOL, brake pad...
Click noise from front brakes only under light brake application and will go away if apply brake harder.
I think the steering column has a sticker that may help, did you do a search on the right upper corner ?
Sounds like your butterfly's are not set correctly for the high idle issue, you may need to remove the carbs again and get you base set adjusted,...
It's the needles and float seat and valves not seating and need replacing.
Yes non-ethanol fuel and inline fuel filter also a good ideal, recheck your wet set too that's where most of my issues ended up being you can read...
I put a light... coat of grease on the the edges of the brake pads where they slide on the surfaces of the caliper hardware, tight is good so that...
Use non ethanol fuel if available in your area...
Nice easy fix if your ok with out your speedo,you can just use your tach RPM for MPH
One of them is a exhaust leak and the whine noise I'm not sure about but maybe in the stator move around the engine with a piece of hose in the...
Me too... but it doe's make sense the way it is installed if you stop and think about it for a bit.
Yes Honda recommends on there retro CB1100 at a service interval also Castro also sells a genetic oil for air cooled fins. Go to U tube and search...
Has anyone have any thought's on air fin oil like Honda recommends on there air cooled motors, I really haven't done much research on this but it...
I remove and install them with a long pry bar 3-4 ft I wrap the area wear I'm prying with form on the driver and install grease on the boots and...
Change mine in the fall so everything sits in fresh oil over the winter and remove and drain the oil filter or change if needed, lucky to put 1 k...
I use my choke as K-Moe says and after warm up my engine idle is about 1100 rpm as spec I believe.
Stock is always the best way to go in my opinion, they were design and engineered for a reason.
How about some photos
That looks like oil residue in the photo, is that the air filter box in the photo with the engine PCV hose going into it, sounds like the...
Wow... low mileage, what kind of condition is it in ?
As I said in past post that's what fixed my uneven plug burn was replacing the floats after taking the carburetors off and on many times and...
Were there LED turn signals or bulbs ? if so that may be your problem.
No more then two line inclement between cylinders I believe and the closer the better.
I used a piece of vacuum hose and lubed it well... and that blocked off the little YICS ports and the hose didn't overheat or damage anything like...
I can't say what is going with your bike, but my experience with my uneven plug burning was that I had little success moving the mixture screws...
I used LED turn signal bulbs and my Turn signals wouldn't flash due to the design of the T/S relay that was original to the bike , so I switched...
I have been trying to understand the theory or mechanics around this issue and can't seem to wrap my head around it. To start I need to correct...
Dave from Hogfiddles figured the issue out. I removed the Carburetors and did a Bench Base Reset of the throttle butterfly's which Dave was kind...
Gauge is good. Light drop, little damage ,sitting at a stop light and braced the fall with my body. Broke the clutch lever, scratched the timing...
Bike run's perfect off idle. Look's like I will be taking the carburetors off.