1. Some members were not receiving emails sent from XJbikes.com. For example: "Forgot your password?" function to reset your password would not send email to some members. I believe this has been resolved now. Please use "Contact Us" form (see page footer link) if you still have email issues. SnoSheriff

    Hello Guest. You have limited privileges and you can't "SEARCH" the forums. Please "Log In" or "Sign Up" for additional functionality. Click HERE to proceed.

Search Results

Search Again
  1. CanuckXJ
    Post

    Vibration Only at 5,000 RPM Up and Down

    the vbration/drone is normal......clanking and rattling isn't. Time to give the bike a good go through as it sounds like something has worked...
    Post by: CanuckXJ, Jun 25, 2017 in forum: XJ Technical Chat
  2. CanuckXJ
    Post

    Vibration Only at 5,000 RPM Up and Down

    I agree with Kmoe, that is just the natural resonance of the motor. Mine does it around 5000-5500 rpm which equates to roughly 105-110 kph on the...
    Post by: CanuckXJ, Jun 25, 2017 in forum: XJ Technical Chat
  3. CanuckXJ
    Post

    XJ650 Intake Manifold / Boot Fix Repair, Heat Shrink. Does it work?

    I didn't watch the video and didn't notice it being mentioned, but the ONLY way I would use heatshrink is if it was labelled "dual wall". The...
    Post by: CanuckXJ, Jun 20, 2017 in forum: XJ DIY How-To Videos
  4. CanuckXJ
    Post

    Opinions on fork seals

    I just put All Balls fork seals/dust boots on my 80 XJ650. Can verify that the dust seal spring is on the outside.
    Post by: CanuckXJ, Jun 20, 2017 in forum: XJ Technical Chat
  5. CanuckXJ
    Post

    Wanted Rear Axel Bearings / Seal Kit

    While that is true for the bearings, their catalog is also great for custom applications (swapping frontends). I've never had an issue with any...
    Post by: CanuckXJ, Jun 5, 2017 in forum: For Sale, Trade/Swap, Wanted
  6. CanuckXJ
    Post

    Wanted Rear Axel Bearings / Seal Kit

    I personally try to use All Balls bearings/seals when available for any of my bikes. I especially like their fork seals.
    Post by: CanuckXJ, Jun 3, 2017 in forum: For Sale, Trade/Swap, Wanted
  7. CanuckXJ
    Post

    Primary/HY-VO adjustment screw?

    Just pulled the side cover (shifter) and it's clean as a whistle in there. Nothing remotely resembling plastic. There was also nothing in the oil...
    Post by: CanuckXJ, May 29, 2017 in forum: XJ Technical Chat
  8. CanuckXJ
    Post

    Primary/HY-VO adjustment screw?

    no difficulty shifting, there's no plastic in there either. I've read all about the primary chain guide falling apart.
    Post by: CanuckXJ, May 29, 2017 in forum: XJ Technical Chat
  9. CanuckXJ
    Post

    Primary/HY-VO adjustment screw?

    Well that clears that up! I noticed it because I was adjusting the cam chain and it looked exactly like the bolt and lock nut on the cam chain...
    Post by: CanuckXJ, May 29, 2017 in forum: XJ Technical Chat
  10. CanuckXJ
    Thread

    Primary/HY-VO adjustment screw?

    Hi, My 80 XJ650 has a bolt and lock nut that goes into the case directly below the cam chain tensioner. I can't find any reference to it online...
    Thread by: CanuckXJ, May 29, 2017, 15 replies, in forum: XJ Technical Chat
  11. CanuckXJ
    Post

    Wanted Y-12 Needle

    Oh indeedy we do lol
    Post by: CanuckXJ, May 28, 2017 in forum: For Sale, Trade/Swap, Wanted
  12. CanuckXJ
    Post

    Wanted Y-12 Needle

    I had a typically loose emulsion tube and I wasn't happy with how tight the main was when I cleaned the carbs out. I went back in there to...
    Post by: CanuckXJ, May 27, 2017 in forum: For Sale, Trade/Swap, Wanted
  13. CanuckXJ
    Post

    Wanted Y-12 Needle

    It's quite possible my oddball is a y-10. it is thicker than the y-12 's. The problem has been sorted and the bike runs beautifully in all ranges...
    Post by: CanuckXJ, May 27, 2017 in forum: For Sale, Trade/Swap, Wanted
  14. CanuckXJ
    Post

    Wanted Y-12 Needle

    Sounds good. Would have been nice if it was standardized in North America, but what can you do.
    Post by: CanuckXJ, May 25, 2017 in forum: For Sale, Trade/Swap, Wanted
  15. CanuckXJ
    Post

    Wanted Y-12 Needle

    I know, I'm in Canada. I'm trying for the single "proper" one first as I only need one, then I'll look into the 10 or 11.......I'm leaning...
    Post by: CanuckXJ, May 25, 2017 in forum: For Sale, Trade/Swap, Wanted
  16. CanuckXJ
    Thread

    Wanted Y-12 Needle

    Hi! Long story short, my 80XJ650 is ready to hit the road and I have had an issue of one cylinder that was running quite rich. I found that 3...
    Thread by: CanuckXJ, May 25, 2017, 15 replies, in forum: For Sale, Trade/Swap, Wanted
Showing results 1 to 16 of 16
Search Again