1. Some members were not receiving emails sent from XJbikes.com. For example: "Forgot your password?" function to reset your password would not send email to some members. I believe this has been resolved now. Please use "Contact Us" form (see page footer link) if you still have email issues. SnoSheriff

    Hello Guest. You have limited privileges and you can't "SEARCH" the forums. Please "Log In" or "Sign Up" for additional functionality. Click HERE to proceed.

Handgrip Selection

Discussion in 'XJ Technical Chat' started by robehend1, Jul 9, 2013.

  1. robehend1

    robehend1 New Member

    Messages:
    18
    Likes Received:
    0
    Trophy Points:
    1
    Location:
    Fargo ND
    Quick question, and comes from me mostly not understanding terminology.

    Does the 82 Xj650 have a 'throttle by wire' setup? I know it has a throttle cable, but again, I'm a bit off on these.

    I'm looking at the Kuryakyn 6345 Universal grips for metrics to replace my OEM grips, as the foam is just about dead. Linked here. Amazon Link

    I'm hoping they fit, bu tit says you need to do a "Throttle by Wire" setup to install them, and not wanting to blow 65 bucks on something I need to send back.
     
    robehend1, Jul 9, 2013
    #1
  2. Polock

    Polock Well-Known Member

    Messages:
    9,751
    Likes Received:
    2,097
    Trophy Points:
    113
    Location:
    Beaver Falls, PA
    Polock, Jul 9, 2013
    #2
  3. jmilliken

    jmilliken Well-Known Member

    Messages:
    1,572
    Likes Received:
    46
    Trophy Points:
    48
    Location:
    Dillsburg, PA
    I like those, but the universal PN is different (6341) on polocks link.....
    Kuryakyn's customer service is pretty good. talk to them... they will set you up right.
     
    jmilliken, Jul 9, 2013
    #3
  4. robehend1

    robehend1 New Member

    Messages:
    18
    Likes Received:
    0
    Trophy Points:
    1
    Location:
    Fargo ND
    Hmm, you're right, the pin is different. I'll have to give them a call and see.

    My only worry is I looked up an install video on youtube, and it said just snap it in, but my throttle has some white tube that just has the grip over it.
     
    robehend1, Jul 9, 2013
    #4
  5. jmilliken

    jmilliken Well-Known Member

    Messages:
    1,572
    Likes Received:
    46
    Trophy Points:
    48
    Location:
    Dillsburg, PA
    yea... that white tube is what controls the throttle cable. The handgrip should go over the white tube.
     
    jmilliken, Jul 9, 2013
    #5
  6. robehend1

    robehend1 New Member

    Messages:
    18
    Likes Received:
    0
    Trophy Points:
    1
    Location:
    Fargo ND
    Found out differently, actually. I picked up the same model 6345 from the local yamaha shop, and tried them. They're designed to replace the white tub, but the neck that inserts into the cable body holder thingy with the starter/kill switch on it is too wide. I've returned them, and had them order me the other one.

    live and learn! Thanks!

    Now to figure out how to mount a rear trailer fender without welding, so my back quits getting covered in junk.
     
    robehend1, Jul 9, 2013
    #6
  7. k-moe

    k-moe Pie, Bacon, Bourbon. Moderator Premium Member

    Messages:
    19,647
    Likes Received:
    6,756
    Trophy Points:
    113
    Location:
    The City of Seven Hills
    Pop Rivets.
     
    k-moe, Jul 9, 2013
    #7
  8. jmilliken

    jmilliken Well-Known Member

    Messages:
    1,572
    Likes Received:
    46
    Trophy Points:
    48
    Location:
    Dillsburg, PA
    JB Weld, Duct Tape and zip ties!
     
    jmilliken, Jul 9, 2013
    #8

Share This Page