1. Hello Guest. You have limited privileges and you can't "SEARCH" the forums. Please "Log In" or "Sign Up" for additional functionality. Click HERE to proceed.

XJ PARTS CATALOG, SECTION G: COOLING SYSTEM

Discussion in 'XJ4Ever - Supporting Vendor' started by chacal, Oct 12, 2013.

Thread Status:
Not open for further replies.
  1. chacal

    chacal Moderator Moderator Supporting Vendor Premium Member

    Messages:
    8,866
    Likes Received:
    1,780
    Trophy Points:
    113
    Location:
    The room where it happened
    SECTION G:


    COOLING SYSTEM PARTS:

    The following service parts are for all of the XJ700-X and XJ750-X water-cooled models.

    Annoying leaks from the many pipes and tubes can be easily fixed with the assortment of o-rings and gaskets listed below.


    Radiator Grill Parts:

    HCP21667 Aftermarket water radiator plastic GRILL DRESS-UP KIT.....contains all the pre-cut pieces of silver chrome edge trim needed to enhance the vertical crossbars on the plastic grill, adding a finished and distinctive look to the grill. Each kit contains a total of 34 pieces: 33 short sections (for each of the short horizontal bars in the grill face) and 1 long section (for the lower edge bar). You can use as many (or as few) of short pieces to create a distinctive pattern; you can even spell out the letter "X" in the grill. Adhesive-infused bright silver chrome edge trim fits into place and holds tight, but can still be easily removed in the future.
    $ 27.95

    HCP21670 Aftermarket water radiator plastic GRILL DRESS-UP KIT.....contains all the pre-cut pieces of golden chrome edge trim needed to enhance the vertical crossbars on the plastic grill, adding a finished and distinctive look to the grill. Each kit contains a total of 34 pieces: 33 short sections (for each of the short horizontal bars in the grill face) and 1 long section (for the lower edge bar). You can use as many (or as few) of short pieces to create a distinctive pattern; you can even spell out the letter "X" in the grill. Adhesive-infused bright golden chrome edge trim fits into place and holds tight, but can still be easily removed in the future.
    $ 27.95


    Radiators and Parts:

    HCP4877 OEM rebuilt RADIATOR, flushed, core cleaned, fins straightened, and repainted, ready for install! This is a rebuilt (used) factory water radiator for all 1985-86 XJ700-X and XJ750-X models. Mounting hardware, hoses, drain plug, etc. are not included. A $ 75.00 core charge applies to this item, and a re-usable, same-model oil cooler must be returned for the core charge to be refunded. NOTE: "re-usable" means it is complete and has not been physically damaged in any way, in particular the drain threads, mounting bracket, and the actual tank itself.
    $ 239.95 + $ 75.00 refundable core charge



    HCP4906 OEM radiator DRAIN PLUG, use 1 on the lower corner of the radiator. For all XJ700-X and XJ750-X models. WARNING: do not over-tighten this drain plug or it will snap off inside the radiator! The factory service manual gives the wrong tightening torque specifications for this plug (twice! and they give two different wrong torque specs!!)........the correct torque spec is 2.2 ft-lbs (30 kg/cm).
    $ 25.95

    HCP4907 OEM radiator drain plug GASKET, use with the drain bolt HCP4906 listed above. For all XJ700-X and XJ750-X models. Each:
    $ 9.95



    HCP3029 OEM radiator MOUNTING BOLT, standard 6-point hex-head alloy steel bolt with a dark finish. Used at the upper center mounting hole. For all XJ700-X and XJ750-X models. Each:
    $ 3.95

    HCP14007 Aftermarket radiator MOUNTING BOLT, standard 6-point hex-head alloy steel bolt with a yellow zinc-plated finish. Used at the upper center mounting hole. For all XJ700-X and XJ750-X models. Each:
    $ 1.95

    HCP22249 Aftermarket radiator MOUNTING BOLT, standard 6-point hex-head 18/8 stainless steel bolt with a bright finish. Used at the upper center mounting hole. For all XJ700-X and XJ750-X models. Each:
    $ 2.95

    HCP14008 Aftermarket radiator MOUNTING BOLT, standard 6-point hex-head 316 stainless steel bolt with a bright finish. Used at the upper center mounting hole. For all XJ700-X and XJ750-X models. Each:
    $ 3.95

    HCP22253 Aftermarket radiator MOUNTING BOLT, standard socket head (allen-key drive) alloy steel with a yellow zinc-plated finish. Used at the upper center mounting hole. For all XJ700-X and XJ750-X models. Each:
    $ 1.95

    HCP228 Aftermarket radiator MOUNTING BOLT, standard socket head (allen-key drive) alloy steel with a black-oxide finish. Used at the upper center mounting hole. For all XJ700-X and XJ750-X models. Each:
    $ 1.95

    HCP2779 Aftermarket radiator MOUNTING BOLT, standard socket head (allen-key drive) alloy steel with a black-oxide finish, features self-locking threads. Used at the upper center mounting hole. For all XJ700-X and XJ750-X models. Each:
    $ 2.95

    HCP226 Aftermarket radiator MOUNTING BOLT, standard socket head (allen-key drive) 18/8 stainless steel with a bright finish. Used at the upper center mounting hole. For all XJ700-X and XJ750-X models. Each:
    $ 2.95



    HCP1902 OEM radiator mounting bolt LOCK WASHER, black oxide-coated alloy steel, used at the upper center mounting holes, for all XJ700-X and XJ750-X models, use 1 per radiator, each:
    $ 6.95

    HCP916 Aftermarket radiator mounting bolt LOCK WASHER, zinc-plated alloy steel with a bright finish, used at the upper center mounting holes, for all XJ700-X and XJ750-X models, use 1 per radiator, each:
    $ 1.95

    HCP319 Aftermarket radiator mounting bolt LOCK WASHER, 18-8 stainless steel, used at the upper center mounting holes, for all XJ700-X and XJ750-X models, use 1 per radiator, each:
    $ 2.95

    HCP321 Aftermarket black oxide-coated alloy steel radiator mounting bolt LOCK WASHER, used at the upper center mounting holes, for all XJ700-X and XJ750-X models, use 1 per radiator. Each:
    $ 1.95



    HCP4896 OEM radiator mounting bolt COLLAR, used at the upper center mounting holes, for all XJ700-X and XJ750-X models, use 1 per radiator.
    $ 6.95

    HCP4894 OEM radiator mounting bolt GROMMET, used at the upper center mounting holes, for all XJ700-X and XJ750-X models, use 1 per radiator.
    $ 7.95



    HCP2533 OEM radiator MOUNTING BOLT, used on all 1985 XJ700-X and XJ750-X models, lower corner mounting holes, use 2 per radiator. The original alloy steel hex-head bolt featured a bright zinc plating, but this superseded version has a black oxide coating. If you desire the original appearance, select either the HCP17146 or HCP17148 bolts below. Each:
    $ 3.95

    HCP17146 Aftermarket radiator MOUNTING BOLT, used on all 1985 XJ700-X and XJ750-X models, lower corner mounting holes, use 2 per radiator. Zinc-plated alloy steel hex-head bolt. Each:
    $ 1.95

    HCP17148 Aftermarket radiator MOUNTING BOLT, used on all 1985 XJ700-X and XJ750-X models, lower corner mounting holes, use 2 per radiator. Bright finish 18-8 stainless steel hex-head bolt. Each:
    $ 2.95

    HCP17147 Aftermarket radiator MOUNTING BOLT, used on all 1985 XJ700-X and XJ750-X models, lower corner mounting holes, use 2 per radiator. Black-oxide coated alloy steel hex-head bolt as original. Each:
    $ 1.95

    HCP2424 Aftermarket radiator MOUNTING BOLT, used on all 1985 XJ700-X and XJ750-X models, lower corner mounting holes, use 2 per radiator. Black oxide coated alloy steel socket head, allen-key drive bolt. Each:
    $ 1.95

    HCP80 Aftermarket radiator MOUNTING BOLT, used on all 1985 XJ700-X and XJ750-X models, lower corner mounting holes, use 2 per radiator. Black oxide coated alloy steel socket head, allen-key drive bolt. Features a small nylon thread patch, making this a self-locking bolt. Each:
    $ 2.95

    HCP2423 Aftermarket radiator MOUNTING BOLT, used on all 1985 XJ700-X and XJ750-X models, lower corner mounting holes, use 2 per radiator. Bright 18-8 stainless steel socket head, allen-key drive bolt. Each:
    $ 2.95



    HCP3029 OEM radiator MOUNTING BOLT, standard 6-point hex-head alloy steel bolt with a dark finish. Used on all 1986 XJ700-X and XJ750-X models, lower corner mounting holes, use 2 per radiator, each:
    $ 3.95

    HCP14007 Aftermarket radiator MOUNTING BOLT, standard 6-point hex-head alloy steel bolt with a yellow zinc-plated finish. Used on all 1986 XJ700-X and XJ750-X models, lower corner mounting holes, use 2 per radiator, each:
    $ 1.95

    HCP22249 Aftermarket radiator MOUNTING BOLT, standard 6-point hex-head 18/8 stainless steel bolt with a bright finish. Used on all 1986 XJ700-X and XJ750-X models, lower corner mounting holes, use 2 per radiator, each:
    $ 2.95

    HCP14008 Aftermarket radiator MOUNTING BOLT, standard 6-point hex-head 316 stainless steel bolt with a bright finish. Used on all 1986 XJ700-X and XJ750-X models, lower corner mounting holes, use 2 per radiator, each:
    $ 3.95

    HCP22253 Aftermarket radiator MOUNTING BOLT, standard socket head (allen-key drive) alloy steel with a yellow zinc-plated finish. Used on all 1986 XJ700-X and XJ750-X models, lower corner mounting holes, use 2 per radiator, each:
    $ 1.95

    HCP228 Aftermarket radiator MOUNTING BOLT, standard socket head (allen-key drive) alloy steel with a black-oxide finish. Used on all 1986 XJ700-X and XJ750-X models, lower corner mounting holes, use 2 per radiator, each:
    $ 1.95

    HCP2779 Aftermarket radiator MOUNTING BOLT, standard socket head (allen-key drive) alloy steel with a black-oxide finish, features self-locking threads. Used on all 1986 XJ700-X and XJ750-X models, lower corner mounting holes, use 2 per radiator, each:
    $ 2.95

    HCP226 Aftermarket radiator MOUNTING BOLT, standard socket head (allen-key drive) 18/8 stainless steel with a bright finish. Used on all 1986 XJ700-X and XJ750-X models, lower corner mounting holes, use 2 per radiator, each:
    $ 2.95



    HCP1902 OEM radiator mounting bolt LOCK WASHER, black oxide-coated alloy steel, used at the lower corner mounting holes, use 2 per radiator, for all XJ700-X and XJ750-X models. Each:
    $ 6.95

    HCP916 Aftermarket radiator mounting bolt LOCK WASHER, zinc-plated alloy steel with a natural finish, used at the lower corner mounting holes, use 2 per radiator, for all XJ700-X and XJ750-X models. Each:
    $ 1.95

    HCP319 Aftermarket radiator mounting bolt LOCK WASHER, 18-8 stainless steel, used at the lower corner mounting holes, use 2 per radiator, for all XJ700-X and XJ750-X models. Each:
    $ 2.95

    HCP321 Aftermarket radiator mounting bolt LOCK WASHER, black oxide-coated alloy steel, used at the lower corner mounting holes, use 2 per radiator, for all XJ700-X and XJ750-X models. Each:
    $ 1.95



    HCP3960 OEM radiator mounting bolt FLAT WASHER, used at the lower corner mounting holes, use 2 per radiator, for all XJ700-X and XJ750-X models. Each:
    $ 2.00

    HCP4895 OEM radiator mounting bolt GROMMET, used at the lower corner mounting holes, use 2 per radiator, for all XJ700-X and XJ750-X models. Each:
    $ 5.95



    HCP4899 OEM radiator grill MOUNTING SCREW, use 3 per radiator, for all XJ700-X and XJ750-X models. Each:
    $ 9.95

    HCP4900 OEM radiator grill mounting screw GROMMET, use 3 per radiator, for all XJ700-X and XJ750-X models. Each:
    $ discontinued


    Coolant System Fan and Switches:

    HCP4891 OEM radiator fan MOTOR. For all XJ700-X and XJ750-X models.
    $ 479.95

    HCP4892 OEM radiator fan BLADES. For all XJ700-X and XJ750-X models.
    $ 119.50


    HCP3276 OEM temperature gauge SENDING UNIT, also known as the "thermo unit" in Yamaha-speak. This is the single terminal sensor that screws into the thermostat housing and which relays information to the temp gauge. For all XJ700-X and XJ750-X models.
    $ 94.95


    HCP3275 OEM fan motor CONTROL SWITCH, also known as the "thermo switch" in Yamaha-speak. This is the dual terminal switch that screws into the thermostat housing and which relays information to the fan, controlling when it turns on and off. Includes its sealing o-ring. For all XJ700-X and XJ750-X models. NOTE: due to the larger-than-original hex on the body of this switch, it will be necessary to file or grind away (dremel “drum” sander or the like) a tiny portion of material around the “curve” of the housing by the switch port……otherwise the switch body will “bottom” on this “curve” before the switch is fully seated and sealed and a small leak will occur. We also suggest that the threads of this switch be wrapped with Teflon tape before installation.
    $ 82.95

    HCP20495 Aftermarket fan motor CONTROL SWITCH, also known as the "thermo switch" in Yamaha-speak. This is the dual terminal switch that screws into the thermostat housing and which relays information to the fan, controlling when it turns on and off. This unit has approximately the same trigger point than the stock control switch. For all XJ700-X and XJ750-X models.
    $ 59.95

    HCP20455 Aftermarket fan motor CONTROL SWITCH, also known as the "thermo switch" in Yamaha-speak. This is the dual terminal switch that screws into the thermostat housing and which relays information to the fan, controlling when it turns on and off. This unit has an approximately 20-degree lower trigger point than the stock control switch, and thus will turn on your fan at a lower coolant temperature (and thus, in hotter environments, more frequently). Highly recommended for people who live in hotter climates. For all XJ700-X and XJ750-X models.
    $ 64.95


    HCP20488 Aftermarket fan motor control switch O-RING, seals the thermo-switch to the thermostat housing. Fits all original or aftermarket thermoswitches. Use 1 per switch on all XJ700-x and XJ750-X models.
    $ 5.95

    NOTE: the HCP3276 thermo sensor uses teflon tape on the sensor threads for sealing, rather than an o-ring.



    Coolant System Thermostat and Pressure Cap:

    HCP4902 OEM cooling system PRESSURE CAP, includes the rubber gasket. NOTE: this replacement cap has a different warning label (it's now orange and white) and a higher pressure rating (1.1 bar vs. the original 0.9 bar) than the original cap, but it fits properly and seals the system correctly. For all XJ700-X and XJ750-X models.
    $ 52.95

    HCP15144 Aftermarket pressure cap WARNING HOT DECAL, round, black decal with silvered lettering. Use on all XJ700-X and XJ750-X models. NOTE: this decal duplicates the original 1985-86 cap decal, and will also fit properly over the Yamaha superseded rad cap, which has a different warning label decal than the original.
    $ 14.95



    HCP4321 OEM radiator cap housing-to-frame MOUNTING BOLT, alloy steel, hex-head bolt with a black finish. Use 2 per housing on all XJ700-X and XJ750-X models. Each:
    $ 3.95

    HCP2745 Aftermarket radiator cap housing-to-frame MOUNTING BOLT, black-oxide coated alloy steel 10mm hex-head bolt has a serrated flange that acts as a lock washer (the OEM bolt does not have a serrated flange nor do they use a lock washer). Use 2 per housing on all XJ700-X and XJ750-X models. Each:
    $ 2.95




    HCP4885 OEM cooling system THERMOSTAT, includes the rubber gasket. For all XJ700-X and XJ750-X models.
    $ 59.95

    HCP10585 Aftermarket cooling system THERMOSTAT, does not include the rubber gasket. Although this thermostat is slightly smaller in diameter than the original, it will still accept your original (or the aftermarket HCP21444) rubber ring gasket, and has the same temperature rating and high-rate water flow capacity as the original. For all XJ700-X and XJ750-X models.
    $ 29.95

    HCP21444 Aftermarket cooling system thermostat RING GASKET, fits snuggly around the outside perimeter of the thermostat and seals against water flow past the thermostat, as well as preventing external water leaks. For all XJ700-X and XJ750-X models.
    $ 14.95



    HCP971 OEM thermostat housing-to-cover BOLT, alloy steel, socket-head cap screw with a black finish. Use 2 per thermostat on all XJ700-X and XJ750-X models. Each:
    $ 7.95

    HCP22253 Aftermarket thermostat housing-to-cover BOLT, alloy steel, socket-head cap screw with a zinc-plated finish. Use 2 per thermostat on all XJ700-X and XJ750-X models. Each: Each:
    $ 1.95

    HCP228 Aftermarket thermostat housing-to-cover BOLT, alloy steel, socket head cap screw with a black-oxide finish. Use 2 per thermostat on all XJ700-X and XJ750-X models. Each:
    $ 1.95

    HCP2779 Aftermarket thermostat housing-to-cover BOLT, alloy steel, socket-head cap screw with a black-oxide coated finish, features self-locking threads. . Use 2 per thermostat on all XJ700-X and XJ750-X models. Each:
    $ 2.95

    HCP226 Aftermarket thermostat housing-to-cover BOLT, 18-8 stainless steel, socket-head cap screw with a bright finish. Use 2 per thermostat on all XJ700-X and XJ750-X models. Each:
    $ 2.95



    HCP3158 OEM thermostat housing-to-frame MOUNTING BOLT, alloy steel, flanged hex-head bolt with a black finish. Use 1 on all XJ700-X and XJ750-X models. Each:
    $ 4.95

    HCP21689 Aftermarket thermostat housing-to-frame MOUNTING BOLT, alloy steel, flanged hex-head bolt with a black finish. Use 1 on all XJ700-X and XJ750-X models. Each:
    $ 2.95



    HCP1901 OEM plastic frame cover-to-frame MOUNTING SCREW, dark grey plated alloy-steel, panhead, phillips-drive, used for the plastic triangle-shaped cover on the right side of the frame tubes, just behind the steering headpipe. Use 1 on XJ700-X and XJ750-X models, each:
    $ 3.95

    HCP21363 Aftermarket plastic frame cover-to-frame MOUNTING SCREW, zinc-plated alloy-steel, panhead, phillips-drive, used for the plastic triangle-shaped cover on the right side of the frame tubes, just behind the steering headpipe. Use 1 on XJ700-X and XJ750-X models, each:
    $ 1.95

    HCP2923 Aftermarket plastic frame cover-to-frame MOUNTING SCREW, 18-8 stainless-steel, panhead, phillips-drive, used for the plastic triangle-shaped cover on the right side of the frame tubes, just behind the steering headpipe. Use 1 on XJ700-X and XJ750-X models, each:
    $ 3.95

    HCP2924 Aftermarket plastic frame cover-to-frame MOUNTING SCREW, black-oxide coated 18-8 stainless steel phillips-drive, panhead screw. Used for the plastic triangle-shaped cover on the right side of the frame tubes, just behind the steering headpipe. Use 1 on XJ700-X and XJ750-X models, each:
    $ 3.95




    HCP1902 OEM plastic frame cover-to-frame mounting screw LOCK WASHER, black oxide-coated alloy steel, use 1 per screw on all XJ700-X and XJ750-X models. Each:
    $ 6.95

    HCP916 Aftermarket plastic frame cover-to-frame mounting screw LOCK WASHER, zinc-plated alloy steel with a bright finish, use 1 per screw on all XJ700-X and XJ750-X models. Each:
    $ 1.95

    HCP319 Aftermarket plastic frame cover-to-frame mounting screw LOCK WASHER, 18-8 stainless steel, use 1 per screw on all XJ700-X and XJ750-X models. Each:
    $ 2.95

    HCP321 Aftermarket plastic frame cover-to-frame mounting screw LOCK WASHER, black oxide-coated alloy steel, use 1 per screw on all XJ700-X and XJ750-X models. Each:
    $ 1.95



    HCP1869 OEM plastic frame cover-to-frame mounting screw FLAT WASHER, black-oxide finish, use 1 per screw on all XJ700-X and XJ750-X models. Each:
    $ 2.95

    HCP6642 Aftermarket plastic frame cover-to-frame mounting screw FLAT WASHER, zinc-plated alloy steel with a bright finish, use 1 per screw on all XJ700-X and XJ750-X models. Each:
    $ 1.95

    HCP6643 Aftermarket plastic frame cover-to-frame mounting screw FLAT WASHER, 18-8 stainless steel with a bright finish, use 1 per screw on all XJ700-X and XJ750-X models. Each:
    $ 2.95

    HCP25756 Aftermarket plastic frame cover-to-frame mounting screw FLAT WASHER, 316 stainless steel with a bright finish, use 1 per screw on all XJ700-X and XJ750-X models. Each:
    $ 3.95

    HCP14285 Aftermarket plastic frame cover-to-frame mounting screw FLAT WASHER, 18-8 stainless steel with a black finish, use 1 per screw on all XJ700-X and XJ750-X models. Each:
    $ 2.95




    Coolant Overflow and Recovery Tank:

    HCP6141 OEM coolant recovery tank CAP, incudes inner rubber seal/diaphram. Fits all XJ700-X and XJ750-X models.
    $ 11.95

    HCP13208 Aftermarket water recovery vent or drain hose RUBBER BOOT, replacement high-temp rubber bellows boot is different in shape and size than original but fits and functions the same. Longer than original and the skinny "head" will need to be trimmed shorter for a proper fit and an original appearance. For all XJ700-X and XJ750-X models.
    $ 6.50

    HCP3782 OEM coolant recovery tank OUTER COVER, black plastic protective and ornamental shroud. For all XJ700-X and XJ750-X models.
    $ 32.95

    HCP10604 OEM coolant recovery tank cover RETAINING SCREW, use 2 per cover, for all XJ700-X and XJ750-X models, each:
    $ 7.95



    Coolant System Fluid Transfer Rubber Hoses and Clamps, Plastic Tubes and Joints, Metal Pipes, and O-Rings:

    Okay, since there is a maze of hoses, pipes, tubes, and o-rings used on these water-cooled models, to help you navigate the entire system, let's start at the beginning, with the RADIATOR........note that we've color-coded the components to be blue to signify fluid that has been through the radiator and thus cooled, and use red to indicate fluid-handling components involved in the movement of heated fluid that has been through the engine, but not yet returned to the radiator for cooling.


    Coming out of the right side of the radiator is the cooled fluid, and it exits the radiator via a short, curved RADIATOR OUTLET HOSE, clamped on each end via the HCP4856 hose clamps, to a long "snake" of a METAL PIPE, which then wraps around the right side of the engine black and goes directly into the WATER PUMP INLET. The HCP4854 o-ring seals this metal pipe where it enters the water pump.

    The water pump itself has a number of both rubber o-ring seals (HCP4849 seals the clutch cover gear access cover to the clutch cover, while the large HCP4847 seals the water pump housing cover), the HCP4840 oil seal, and even an internal MECHANICAL SEAL (HCP4843), along with all the typical water-pumpy type of items needed to pressurize the fluid: a vaned impeller connected via a set of gears to a drive shaft, along with the usual assortment of spacers, collars, bearings, etc.

    Coming out of the WATER PUMP OUTLET is a right-angle PLASTIC JOINT, sealed to the water pump via the HCP4859 o-ring, leading directly into a short METAL CONNECTOR PIPE (sealed on both its inlet and outlet ends by the HCP4861 o-rings) that transfers the fluid to the two PLASTIC INLET JOINTS bolted to the cylinder jugs. These two plastic inlet joints are connected to each other via a short METAL TRANSFER PIPE, sealed on either end to those plastic inlet joints via the HCP4869 o-rings) and all of the above joints use their own unique HCP4864 oval rings where they mate to the cylinder jugs.

    Then, after the fluid has run around inside the upper end of the engine for a while and gotten hot, it exits the rear of the cylinder head via two METAL RETURN PIPES, each one using one of the HCP4869 o-ring at these pipe-to-cylinder head joints. These metal pipes are clamped to RUBBER RETURN HOSES that go to the thermostat housing; coming out of this thermo housing is the large RUBBER RETURN HOSE to the inlet flange (upper) on the radiator itself, where the HCP4856 screw clamp holds it firmly in place.

    Of course, all of the large rubber hoses have a worm-screw style CLAMP to secure it to it mating tube or flange, while the smaller hoses use a spring or scissors type clamp or clip.

    A couple of other points of interest and we'll conclude our tour: coming out of the water pump is a small diameter SYSTEM BY-PASS HOSE which runs to the right side metal return pipe (coming out of the cylinder head), and is held in place by the HCP4876 spring clips on each end. The by-pass hose is an "emergency escape valve" in case any part of the system gets partially or fully blocked. It is secured on each end by a special clip-type clamp.

    Finally, there is the plastic OVERFLOW TANK or RESERVOIR which takes in or releases fluid from a long rubber OVERFLOW HOSE hose that runs from a small nipple coming off the PRESSURE CAP HOUSING to the inlet nipple on the bottom of the overflow tank; the HCP122 or HCP16428 spring type pinch clamp is used on the radiator cap housing end of this hose, while the HCP6142 scissors clip cinches this hose to the overflow tank.

    The top of the overflow tank is home to a small rubber VENT and DRAIN HOSE that takes care of massive fluid overflows; this thin rubber hose attaches to the overflow tank via a small, flexible, rubber accordion boot (there is no tank nipple for this drain hose, just a round hole in the top of the tank) and then is routed down the left side frame tube and then in-between the #2 and #3 exhaust header pipes, captured by a little clamp on the frame cross tube (above the oil filter housing), and then just dangles down unceremoniously toward the ground, waiting to puke out any massively over-heated engine coolant onto the ground, directly in the travel path of your rear wheel......


    Hoses and Clamps:

    HCP4856 OEM radiator hose CLAMP worm-screw type is identical to original and features a slotted hex-head screw driving a partially slotted, stainless steel band. Use 6 per bike in the following locations: 1 at each end of the thermostat housing-to-pressure cap housing transfer hose joints, and 1 at each end of the fluid return hoses, both at their metal pipe connection and the thermostat housing ends. Each:
    $ 9.95

    HCP12237 Aftermarket radiator hose CLAMP worm-screw type is identical to original and features a slotted hex-head screw driving a partially slotted, stainless steel band. Use 6 per bike in the following locations: 1 at each end of the thermostat housing-to-pressure cap housing transfer hose joints, and 1 at each end of the fluid return hoses, both at their metal pipe connection and the thermostat housing ends. Each:
    $ 2.95



    HCP4888 OEM radiator hose CLAMP worm-screw type is identical to original and features a slotted hex-head screw driving a partially slotted, stainless steel band. Use 1 per bike in the following locations: on the radiator inlet hose at the thermostat housing. Each:
    $ 6.25

    HCP12238 Aftermarket radiator hose CLAMP worm-screw type is identical to original and features a slotted hex-head screw driving a partially slotted, stainless steel band. Use 1 per bike in the following locations: on the radiator inlet hose at the thermostat housing. Each:
    $ 1.25



    HCP12239 Aftermarket radiator hose CLAMP worm-screw type is identical to original and features a slotted hex-head screw driving a partially slotted, stainless steel band. Use 3 per bike in the following locations:
    1 at each end of the radiator outlet hose-to-metal transfer pipe joints, and 1 on the radiator inlet hose at the radiator. Each:
    $ 1.20



    HCP12671 Aftermarket water pump-to-right return pipe SYSTEM BY-PASS HOSE, correct size high-temp rubber hose that runs from the water pump housing to the right side metal fluid return pipe. Hose is cut generously long and may need to be trimmed slightly for an exceptional fit.
    $ 4.50

    HCP4876 OEM system by-pass hose PINCH CLAMP, use one at each end. Each:
    $ 1.25



    HCP12672 Aftermarket water recovery tank OVERFLOW HOSE, correct size high-temp rubber hose that runs from the overflow tank lower outlet nipple to the pressure cap housing nipple. Hose is cut generously long and may need to be trimmed slightly for an exceptional fit.
    $ 5.95


    HCP122 OEM recovery tank overflow hose WIRE CLAMP, fitted at the radiator cap housing end of the hose that runs from the radiator cap housing to the coolant recovery tank. Each:
    $ 7.95

    HCP16428 Aftermarket recovery tank overflow hose WIRE CLAMP, fitted at the radiator cap housing end of the hose that runs from the radiator cap housing to the coolant recovery tank. Same style clamp as the original HCP122 clamp. Each:
    $ 4.95

    HCP24883 Aftermarket recovery tank overflow hose BAND CLAMP, fitted at the radiator cap housing end of the hose that runs from the radiator cap housing to the coolant recovery tank. Can be used to replace the HCP122 wire-style clamp above. Each:
    $ 5.95


    HCP6142 OEM recovery tank overflow hose BAND CLAMP, fitted at the recovery tank end of the hose that runs from the radiator cap housing to the coolant recovery tank. Each:
    $ 7.95

    HCP24884 Aftermarket recovery tank overflow hose BAND CLAMP, fitted at the recovery tank end of the hose that runs from the radiator cap housing to the coolant recovery tank. Can be used to replace original clamp HCP6142 above. Each:
    $ 5.95




    HCP12673 Aftermarket water recovery tank-to-atmosphere VENT or DRAIN HOSE, correct size high-temp rubber hose that runs from the overflow tank upper cap to the atmosphere. Hose is cut generously long and may need to be trimmed slightly for an exceptional fit. This hose uses no securing clamps, but the end that fits into the recovery jar cap has a small securing rubber bellows boot that is not included.
    $ 5.50

    HCP13208 Aftermarket water recovery vent or drain hose RUBBER BOOT, replacement high-temp rubber bellows boot is different in shape and size than original but fits and functions the same. Longer than original and may be trimmed shorter for a more original appearance.
    $ 6.50



    Water Pipe Fitting Seals and O-rings:

    We recommend the use of silicone grease when installing any of these seals or o-rings:

    HCP28407 Aftermarket o-ring, oil seal, and gasket installation pure SILICONE GREASE. This small 5-gram (1/6-oz) snap-open "pillow packet" is enough for a few small oil seals, dozens of o-rings, and the like. Each:
    $ 4.95

    HCP1714 Aftermarket o-ring, oil seal, and gasket installation pure SILICONE GREASE. This generous 14-gram (1/2-oz.) tub goes a long way, because just like Brylcreem, "just a little dab will do ya'!" Each:
    $ 9.95


    HCP4869 OEM metal pipe round O-RING, use one on each of the metal radiator return pipes where they exit the cylinder head, and one on each end of the cylinder head inlet joints metal transfer pipe ends (where the metal transfer pipe joins into the plastic cylinder head inlet joints) There are thus a total of 4 of these o-rings used per engine. Each:
    $ 7.95

    HCP4864 OEM connecting joint OVAL O-RING, use 2 per system on the plastic pipes that bolt to the cylinder jugs and allow cooled fluid to enter the engine. Each:
    $ 7.95

    HCP4861 OEM plastic connecting tube #2 round O-RING, use 1 on each end. Each:
    $ 7.95



    HCP5833 OEM cylinder jugs (front) and cam case water jacket DRAIN PLUG, use 3 per engine on all XJ700-X and XJ750-X engines. Each:
    $ 4.95


    HCP4258 OEM radiator-to-water metal pipe FLANGED DRAIN PLUG, for all XJ700-X and XJ750-X models. Use 1 per bike.
    $ 7.95

    HCP22181 Aftermarket radiator-to-water metal pipe FLANGED DRAIN PLUG, for all XJ700-X and XJ750-X models. 6-point hex head alloy steel fastener has a serrated flange (which eliminates the need for using a lockwasher) and features a dark finish. Use 1 per bike. Each:
    $ 2.95


    HCP12935 OEM thermostat housing DRAIN PLUG, for all XJ700-X and XJ750-X models. Use 1 per bike.
    $ 7.95


    HCP4853 OEM system drain bolts copper CRUSH WASHER. Use 1 each on the cam case rear drain bolt, the cylinder jugs front drain bolts, the radiator-to-water-pump inlet pipe, and on the thermostat housing drain bolt. Each:
    $ 9.95

    HCP20671 Aftermarket system drain bolts copper CRUSH WASHER. Use 1 each on the cam case rear drain bolt, the cylinder jugs front drain bolts, the radiator-to-water-pump inlet pipe, and on the thermostat housing drain bolt. Each:
    $ 6.95



    HCP4847 OEM water pump housing cover large round O-RING, use 1 per pump. Each:
    $ 39.95

    HCP20590 Aftermarket water pump housing cover large round O-RING, use 1 per pump. This o-ring is the same length and thickness as the original o-ring, but is shaped very slightly different from the original, but can be hand-formed to the proper shape and performs correctly. Each:
    $ 29.95


    HCP4849 OEM water pump housing-to-block round O-RING, use 1 per pump. Each:
    $ 12.95

    HCP4859 OEM water pump inlet-to-joint round O-RING, use 1 per bike. Each:
    $ 4.95

    HCP4854 OEM radiator outlet pipe (to water pump) round O-RING, at the water pump, use 1 per bike. Each:
    $ 7.95



    HCP4279 OEM water pump inlet coolant pipe mounting BOLT, for all XJ700-X and XJ750-X engines. Attaches the pump at the pump inlet. Use 1. Each:
    $ 7.95



    HCP1902 OEM water pump inlet coolant pipe mounting bolt LOCK WASHER, black oxide-coated alloy steel, use 1 on all XJ700-X and XJ750-X engines. Each:
    $ 6.95

    HCP916 Aftermarket water pump inlet coolant pipe mounting bolt LOCK WASHER, zinc-plated alloy steel with a bright finish, use 1 on all XJ700-X and XJ750-X engines. Each:
    $ 1.95

    HCP319 Aftermarket water pump inlet coolant pipe mounting bolt LOCK WASHER, 18-8 stainless steel, use 1 on all XJ700-X and XJ750-X engines. Each:
    $ 2.95

    HCP321 Aftermarket water pump inlet coolant pipe mounting bolt LOCK WASHER, black oxide-coated alloy steel, use 1 on all XJ700-X and XJ750-X engines. Each:
    $ 1.95




    HCP1869 OEM water pump inlet coolant pipe mounting bolt FLAT WASHER, use 1 on all XJ700-X and XJ750-X engines, black-oxide finish, each:
    $ 2.95

    HCP6642 Aftermarket zinc-plated alloy steel with a natural finish, water pump inlet coolant pipe mounting bolt FLAT WASHER, use 1 on all XJ700-X and XJ750-X engines, each:
    $ 1.95

    HCP6643 Aftermarket 18-8 stainless steel water pump inlet coolant pipe mounting bolt FLAT WASHER, use 1 on all XJ700-X and XJ750-X engines, each:
    $ 2.95

    HCP25756 Aftermarket 316 stainless steel water pump inlet coolant pipe mounting bolt FLAT WASHER, use 1 on all XJ700-X and XJ750-X engines, each:
    $ 3.95

    HCP14285 Aftermarket black oxide-coated 18-8 stainless steel water pump inlet coolant pipe mounting bolt FLAT WASHER, use 1 on all XJ700-X and XJ750-X engines, each:
    $ 2.95




    HCP10864 OEM water pump round access cover plate O-RING, on the main clutch cover.
    $ 12.95

    HCP10865 OEM water pump round access cover plate mounting SCREW, on the main clutch cover, black finish, use 2 per cover, each:
    $ 7.95

    HCP14002 Aftermarket water pump round access cover plate mounting SCREW, on the main clutch cover, black-oxide coated 18-8 stainless steel, phillips drive as original, use 2 per cover, each:
    $ 2.95

    HCP14004 Aftermarket water pump round access cover plate mounting SCREW, on the main clutch cover, bright polished 18-8 stainless steel, phillips drive as original, use 2 per cover, each:
    $ 2.95


    HCP14006 Aftermarket water pump round access cover plate mounting SCREW, on the main clutch cover, black-oxide coated alloy steel, allen-key drive, use 2 per cover, each:
    $ 1.95

    HCP14005 Aftermarket water pump round access cover plate mounting SCREW, on the main clutch cover, bright polished 18-8 stainless steel, allen-key drive, use 2 per cover, each:
    $ 2.95



    Water Pump Internal Parts:

    HCP4874 OEM water pump countershaft BEARING, use 1 per shaft. Each:
    $ 52.95

    HCP4842 OEM water pump impeller shaft BEARING, use 1 per shaft. Each:
    $ 29.95



    HCP4843 OEM water pump impeller shaft MECHANICAL SEAL, use 1 per shaft on all XJ700-X and XJ750-X engines. Also fits the following bikes: 1999-05 YZF-R6, 2006-09 YZF-R6S, 1986-87 FZX700 Fazer, 1998 YZF750R, 1994 GTS1000. 2001-08 YZF1000R, 1992-95 FZR1000R, 1998-06 YZF-R1, 1985-07 VMX12 V-Max, 1986-93 XVZ13 Venture, 2001 XVZ1300AN Royal Star Boulevard, 2002-13 XVZ13TF Royal Star Venture, and 2005-10 XVZ13CT Royal Star Deluxe. Each:
    $ 59.95

    HCP11692 Aftermarket water pump impeller shaft MECHANICAL SEAL, use 1 per shaft on all XJ700-X and XJ750-X models. Also fits all of the following models: 1999-05 YZF-R6, 2006-09 YZF-R6S, 1986-87 FZX700 Fazer, 2001-08 YZF1000, 1998-06 YZF-R1, 1985-07 VMX12 V-Max, 1986-93 XVZ13 Venture, 2001 XVZ1300 Royal Star Boulevard, 2002-13 XVZ13 Royal Star Venture, and 2005-10 XVZ13 Royal Star Deluxe models.
    Each:
    $ 49.95



    HCP4840 OEM water pump impeller shaft housing OIL SEAL, use 1 per shaft housing on all XJ700-X and XJ750-X engines. Each:
    $ 13.95

    HCP20946 Aftermarket water pump impeller shaft housing OIL SEAL, use 1 per shaft. Each:
    $ 9.95




    Radiator Coolant:

    The use of the proper, non-corrosive and compatible radiator COOLANT is especially important on aluminum engines, as many of the typical additives in standard coolant products contain chemicals that will lead to the corrosion of aluminum and the build-up of hard deposits that will reduce the cooling effectiveness of your system.

    We offer both a conventional ethylene-glycol based coolant and an environmentally-friendly, non-poisonous propylene-glycol based fluid, both pre-mixed at a proper ratio, to provide both temperature protection from 26 degree below zero to 265-F and will not harm or clog your expensive X engine!


    The factory recommends a coolant change every 24 months, using an ethylene-glycol based coolant (or equivalent) with anti-corrosion inhibitors for aluminum system, mixed 50% with water. The fluid capacity of the entire system is 2.5 quarts, and another 0.5 quart for the reservoir......so a single gallon bottle of pre-mixed coolant will do you well.

    The proper fluid drain, change, and refill procedure involves removing the radiator cap, then the radiator drain plug, and finally removing all 5 of the small drain bolts located at various positions on the system:

    * the 2 small drain bolts located on the front of the cylinder jugs (just outside of the #1 and #4 exhaust header pipes)
    * the 1 small drain bolt located on the rear side of the cylinder jugs
    * the 1 small drain bolt located on the bottom of the thermostat housing
    * and 1 final small drain bolt located on the metal pipe that snakes around the right side of the engine, from the radiator outlet to the water pump inlet.

    All of these small drain bolts and the radiator drain plug use thin gaskets which should be renewed.

    Now let all of the fluid drain, which may take a while, and then replace all of the drain bolts and the radiator drain plug (do not overtighten!)

    Remove the plastic fluid overflow tank and reservoir and clean it out thoroughly.

    Finally, refill the system slowly from the radiator cap, and let air bubbles work their way out of the system (it takes time!). Remember that the overflow tank and reservoir takes fluid from the radiator cap neck, so until the system is full, none of the fluid is going to fill the reservoir!

    Once full, start the engine and let it warm up with the cap off. Keep re-filling the system until it is completely full. Make sure that the fan comes on once the gauge moves into the "red zone", and also check to make sure that the thermostat is working correctly.

    Now dispose of the old coolant properly, replace the radiator cap, and go for a ride!

    You can review the proper coolant flush procedures at:

    http://www.xj4ever.com/maxim-x coolant flush.pdf


    NOTE: the following product(s) can only be shipped via ground transport (which thus eliminates the postal Priority Mail, postal Express Mail, or private carrier Expedited levels of service for this item) and cannot (and will not----don't even ask!) be shipped outside of the continental USA. Additionally, there may be a per-package weight or quantity restriction, and thus multiple-unit orders of this product may have to be shipped in separate packages and will incur additional shipping charges.

    HCP11485 Aftermarket pre-mixed COOLANT, ethylene-glycol based formula (toxic). Contains no phosphates, silicates, nitrates, amines, or borax, additives which are not compatible with aluminum engines. Comes in a 1-gallon jug, protects from -34F to 265F when used in a closed, 15-pound pressurized system.
    $ 37.95

    HCP11486 Aftermarket pre-mixed COOLANT, propylene-glycol based formula (non-toxic). Contains no phosphates, silicates, nitrates, amines, or borax, additives which are not compatible with aluminum engines. Comes in a 1-gallon jug, protects from -34F to 265F when used in a closed, 15-pound pressurized system.
    $ 37.95



    Cooling System Tools:

    NOTE THE FOLLOWING TOOL IS AVAILABLE FOR RENTAL!!: some tools are a one-time or infrequent use tool, so it may be more economical for you to rent them from us, rather than to purchase outright. Please see the “rental” section within the THE TOOLBOX section of our catalog at:

    http://xjbikes.com/forums/index.php?threads/xj-parts-catalog-section-p-the-toolbox.44630

    and review the availability and procedures in the TOOL RENTAL section.


    HCP9236 Aftermarket water pump MECHANICAL SEAL INSTALLER TOOL, nice copy of the original tool used on all the XJ700-X and XJ750-X models. Includes a proper length bolt to use as a driver “handle”.
    $ 89.95
     
    Last edited: Feb 12, 2024
  2. chacal

    chacal Moderator Moderator Supporting Vendor Premium Member

    Messages:
    8,866
    Likes Received:
    1,780
    Trophy Points:
    113
    Location:
    The room where it happened
    ..
     
  3. chacal

    chacal Moderator Moderator Supporting Vendor Premium Member

    Messages:
    8,866
    Likes Received:
    1,780
    Trophy Points:
    113
    Location:
    The room where it happened
    ...
     
  4. chacal

    chacal Moderator Moderator Supporting Vendor Premium Member

    Messages:
    8,866
    Likes Received:
    1,780
    Trophy Points:
    113
    Location:
    The room where it happened
    .v
     
  5. chacal

    chacal Moderator Moderator Supporting Vendor Premium Member

    Messages:
    8,866
    Likes Received:
    1,780
    Trophy Points:
    113
    Location:
    The room where it happened
    .v.
     
  6. chacal

    chacal Moderator Moderator Supporting Vendor Premium Member

    Messages:
    8,866
    Likes Received:
    1,780
    Trophy Points:
    113
    Location:
    The room where it happened
    vi
     
Thread Status:
Not open for further replies.

Share This Page